BOTTLEHEAD’S BLACK FRIDAY & CYBER MONDAY SALE IS ON! SAVE 15% ON AMP KITS & MODS, PLUS SPECIAL PRICING ON COMBOS. OTHER DISCOUNTS (VOLUME, ADD-ON OFFERS, ETC.) CANNOT BE APPLIED DURING THE SALE. 

--

Days

--

Hours

--

Mins

--

Secs

The Eros 2 has built a word-of-mouth reputation as an excellent phono preamp for vinyl setups. Assembled from the stock kit, the Eros 2 handles most moving magnet (MM) and high-output moving coil (HOMC) cartridges. However, the Eros 2 can be upgraded with step-up transformers (SUTs) to work well with many low-output moving coil cartridges (LOMC) as well.

Incorporated into the Eros 2 chassis are a couple of holes for mounting step-up transformers. Terminals have been left available to provide convenient locations for secondary loading resistors. Primary loading resistors and loading caps can be installed across each RCA jack.

It is important to choose the right transformer ratio for your cartridge. Check your cartridge's specs to get its output voltage. The Eros 2 performs best when it outputs about 4mV-5mV nominal, so pick a ratio that puts you somewhere in that range. For instance: a 0.4mV LOMC signal into a 1:10 transformer will give you a nominal output level of 4mV, which is right where you want to be with an Eros 2.

While there are a handful of transformer manufacturers, there are a couple where we have more hands-on experience. 

The general process for installing these transformers in an Eros 2 is as follows:

  1. Pop the resistors out of each RCA jack that go to pin 9 on each EF86 (leave them attached to the socket, just pop out the end sitting in the solder cup of the RCA jack).
  2. Remove the 47K loading resistor on each RCA jack.
  3. Reconnect them at terminals 2 and 17.
  4. Install step-up transformers.
  5. Wire step-up primary wires to each RCA jack.
  6. Wire step-up secondary wires to terminals 1/2 and 16/17.
  7. Install loading resistors as recommended by the SUT manufacturer and/or your cartridge manufacturer.  You can load the primary or the secondary of the SUT relatively easily by either using loading resistors across the RCA jacks (loading the primary), or loading resistors between 1/2 and 16/17 (loading the secondary).

The Bottlehead Forums are here to help with any questions you may have. In fact, this post was adapted from a thread by Paul Birkeland (and with contributions from Paul Joppa and Dan Schmalle). Check it out for more information and photos.

Bottleblog Posts

View all

Eros 2 and Step-Up Transformers - Bottlehead

Eros 2 and Step-Up Transformers

The Eros 2 has built a word-of-mouth reputation as an excellent phono preamp for vinyl setups. Assembled from the stock kit, the Eros 2 handles most moving magnet (MM) and high-output moving coil (HOMC) cartridges. However, the Eros 2 can be upgraded with step-up transformers (SUTs) to work well with many low-output moving coil cartridges (LOMC) as well.

Read moreabout Eros 2 and Step-Up Transformers

Bottlehead's Amp Compatibility Tool - Bottlehead

Bottlehead's Amp Compatibility Tool

One of the questions we get most often is whether a particular Bottlehead amplifier will work well with someone’s speakers. It’s a reasonable question, and the answer, unfortunately is usually "it depends." How efficient are your speakers? How far away do you sit? What's your room like? How loudly do you like to listen?

We built a new tool to help answer that question.

Read moreabout Bottlehead's Amp Compatibility Tool

Picking the Right Kit for your Skill Level - Bottlehead

Picking the Right Kit for your Skill Level

Bottlehead assigns a level to each product in the lineup to help builders understand which kits are best to fit their abilities. Read on to see what those levels mean for you.

Read moreabout Picking the Right Kit for your Skill Level